CC |
Run a custom control.
- Press Bank and use the Bank knob to select the bank you want to run the CC from.
- Press Macro and use the Macro knob to select the CC you want to run.
|
ClearAllFB
|
Clear all frame-buffers. |
ClearFB
|
Clear a specific frame-buffer.
- Press Buffer ID and use the Buffer ID knob to select the frame-buffer you want to use.
|
ClearLayerFB
|
Clear a specific layer in a specific frame-buffer.
- Press Layer ID and use the Layer ID knob to select the layer you want to use.
- Press Buffer ID and use the Buffer ID knob to select the frame-buffer you want to use.
|
Down
|
Move the current selection in the Sequencer to the item below in the list. |
Focus
|
Set the Sequencer focus to a specific template.
- Press Take ID and use the Take ID knob to select the take id for the template you want to load.
|
FTB
|
Perform a fade to black transition. |
GPI
|
Trigger a GPI.
- Use the GPI knob to select the GPI that you want to use.
|
GPI w/State
|
Turn a GPI on or off.
- Press GPI and use the GPI knob to select the GPI that you want to use.
- Press State and use the State knob to select whether to turn the GPI on (On or
1) or off (Off or 0).
|
HELP
|
This command is not implemented at this time. |
KEYAUTO
|
Perform a key only auto transition on the selected ME.
- Select the ME X that you want to perform the transition on.
- Select the Key X that you want to transition.
|
KEYCUT
|
Perform a key only cut transition on the selected ME.
- Select the ME X that you want to perform the transition on.
- Select the Key X that you want to transition.
|
KEYSHAPED
|
Turn shaped keying on or off for the selected key.
- Select the ME X that you want set the key for.
- Select the Key X that you want to change the state for.
- Press State and use the State knob to select whether the alpha is shaped (On) or unshaped
(Off).
|
KEYSTATE
|
Returns whether a key is on-air or off-air on an ME.
- Select the ME X and Key X for the key you want to get the sate for.
|
LOADSET |
Recall a switcher set.
- Press Disk and use the Disk knob to select the location of the set you want to recall.
- Press Set, enter the name of the set you want to recall, and press Accept New Name.
|
MEAUTO |
Perform an auto transition on the selected ME.
- Select the ME X(s) that you want to perform the transition on.
|
MECUT |
Perform a cut on the selected ME.
- Select the ME X(s) that you want to perform the transition on.
|
MEM |
Recall a memory.
- Select the ME X(s) that you want to recall the memory on.
- Press Memory and use the Memory knob to select the memory you want to recall.
|
MEMSAVE |
Store a memory.
- Select the ME X(s) that you want to store the memory on.
- Press Memory and use the Memory knob to select the memory you want to store.
|
MNEM
|
Enter a new mnemonic name for a source.
- Select the type of source and use the Src X knob to select the source you want to name. You may have to press the Src
X to have the knob appear.
- Press Name, enter the name of the set you want to store, and press Accept New Name.
|
MS |
Load a media item into a Media-Store.
- Press GS, GSA, or ME and use the GS, GSA, or ME knob to select the Media-Store you want to load the media
item on.
- Press Channel and use the Channel knob to select the channel of the selected Media-Store that you want to
load a media item on.
- Press Media Number and use the Media Number knob to select the media item you want to load.
|
MSPLAY
|
Play the current media item loaded in the selected Media-Store.
- Press GS, GSA, or ME and use the GS, GSA, or ME knob to select the Media-Store you want to play the media
item on.
- Press Channel and use the Channel knob to select the channel of the selected Media-Store that you want to
play the media item on.
|
MVBOX
|
Select a source for a box on a MultiViewer.
- Select the type of source you want to select and use the Src X knob to select the source you want to select.
- Press MV and use the MV knob to select the MultiViewer you want to select a source on.
- Press Box and use the Box knob to select the box on the MultiViewer that you want to assign the
source to.
|
Next
|
Take the current selection in the Sequencer to air and advance the current selection to the next item in the list. |
Read
|
Take the current selection in the Sequencer to air. |
RESETALL
|
Performs an ALL+ALL soft reset on the switcher. |
Resume
|
Resume a specific layer in a specific frame-buffer.
- Press Layer ID and use the Layer ID knob to select the layer you want to use.
- Press Buffer ID and use the Buffer ID knob to select the frame-buffer you want to use.
|
SAVESET |
Store a switcher set.
- Press Disk and use the Disk knob to select the location of the set you want to store.
- Press Set, enter the name of the set you want to store, and press Accept New Name.
|
SeqIn
|
Load a template to air on a specific layer to the output channel selected in the template. The Sequencer focus moves to this item.
- Press Take ID and use the Take ID knob to select the take id for the template you want to load.
- Press Layer ID and use the Layer ID knob to select the layer you want to use.
|
SeqOut
|
Take a template off-air.
- Press Take ID and use the Take ID knob to select the take id for the template you want to load.
|
SETVIDMODE
|
Set the video format that you want the switcher to operate in.
- Press Vid/Ref and use the Vid/Ref knob to select VID.
- Press Format and use the Format knob to select the video format you want the switcher to operate in.
|
SpyderBPR
|
Recall an existing basic preset Preset ID on the device. |
SpyderFKR
|
Recall a single predefined function key Function Key on the device. |
SpyderRSC
|
Recall a register Register ID at a specific cue Script Cue on the device. |
Take
|
Load a template to air in a specific frame-buffer and on a specific layer.
- Press Take ID and use the Take ID knob to select the take id for the template you want to load.
- Press Layer ID and use the Layer ID knob to select the layer you want to use.
- Press Buffer ID and use the Buffer ID knob to select the frame-buffer you want to use.
|
TRANSINC
|
Select what is included in the next ME transition.
- Press the ME X button for the ME that you want to set the next transition for.
- Select the key(s) and/or background that you want to include in the next transition.
|
TRANSRATE
|
Select a new transition rate for an ME.
- Press the ME X button for the ME that you want to set the new rate for.
- Press Num of Frames and use the Num of Frames knob to select the length of the transition in frames.
|
TRANSTYPE
|
Select a transition type for an ME.
- Press the ME X button for the ME that you want to set the transition type for.
- Press Type and use the Type knob to select the type of transition you want to perform.
|
TypeInCmd
|
Enter a manual RossTalk command. |
USERVAR
|
Select the variable name, operation, and value you want to apply to the user variable.
- Press Name and enter the name of the variable you want to edit.
- Press Variable Operator and use the Variable Operator knob to select the operator you want to apply.
- Press Variable Value and use the Variable Value knob to select the value you want to apply.
|
Up
|
Move the current selection in the Sequencer to the item above in the list. |
XPT
|
Select a source on a bus on the switcher.
- Select the type of source and use the Src X knob to select the source you want to select. You may have to press the Src
X to have the knob appear.
- Select the aux, ME, or key that you want to select the source on. Depending on the source, you may have to select a key bus or aux bank.
|